Your location:  Home  >  Bearing News  >  China Market
<<  Back

Restart after the disaster, you and me ! How to deal with machine water, three steps to help you solve the problem !

Resource from:  CBCC Likes:184
Aug 03,2021

In July, Henan Province was hit by heavy rains in history. Then the strong typhoon "Fireworks" came fiercely and hit Zhejiang, Shanghai and other places. Many places were affected by extremely heavy rainfall and caused heavy losses. The sudden disaster affects the hearts of the people across the country, and Rifa Seiki employees empathize with it. In order to help "RIFA" customers resume production as soon as possible, we provide the following services:

Assist customers to provide equipment cleaning and maintenance services for free

Priority arrangements for customers after the disaster until the equipment is used normally

Parts and accessories affected by the disaster are supplied at the company's purchase cost price

Provide you with 7×24 hours of professional services (Information Processing Center: 800-8575520)

Water treatment method for machine tool

When encountering heavy rains, for workshops with low terrain and easy access to water, waterproof measures must be taken in advance to avoid water wading as much as possible. If your machine tool has been flooded, first check the flooded part carefully and deal with it as follows:

01

Mechanical part

1. Thoroughly clean the machine tool and its components. Be sure to rinse the remaining sand and disassemble it, clean it up and fully dry it;

2. Dry enough and lubricate with oil to avoid corrosion and affect accuracy;

3. Clean or replace the lead screw and bearing;

4. Check the pneumatic pipeline, lubricate the pipeline, and then connect it after cleaning;

5. It is recommended to use anti-rust water or grinding fluid to clean the inside of the equipment, and do a good job of anti-rust.

 

02

Hydraulic part

1. The motor oil pump cannot be turned on, because the water in the hydraulic oil may enter the hydraulic piping system of the machine after turning on the motor, causing the metal hydraulic components to rust. The hydraulic motor needs to be cleaned and dried, and the measuring motor can be used without leakage;

2. Replace all hydraulic oil, wipe the oil tank clean with kerosene and a clean cotton cloth before changing the oil.

 

03

Electrical control part

1. Disconnect all power supplies and turn off all switches of the machine tool;

2. Remove the electrical components in the electrical box, clean and fully dry;

3. Use a multimeter to detect whether the output of the switching power supply is short-circuited;

4. Detect whether there is a short circuit between each input and output common terminal and the signal;

5. Carefully inspect the circuit, system interface and other parts to avoid short-circuit failure;

6. Inspect the completely dry electrical components separately, and then install them and use them only after they are intact;

7. Clean the equipment transformer and use it after the measurement is normal.

8. Remove the system battery as soon as possible. After cleaning and fully drying the servo motor and control system, send it to a special agency for testing before use;

9. Servo motor connection line, power line and encoder line connector are disconnected and dried with high-pressure air before connecting;

 

CAUTION !  

 After the above steps are completed, the parts are assembled again and the test machine is electrified.

If abnormal, please shut down immediately, and cut off the power supply, contact us.

Work together, rain and wind !  

The daily hairdressing machine will be with you, peer !


(CBCC)
【CBCC News Statement】
1.The news above mentioned with detailed source are from internet.We are trying our best to assure they are accurate ,timely and safe so as to let bearing users and sellers read more related info.However, it doesn't mean we agree with any point of view referred in above contents and we are not responsible for the authenticity. If you want to publish the news,please note the source and you will be legally responsible for the news published.
2.All news edited and translated by us are specially noted the source"CBCC".
3.For investors,please be cautious for all news.We don't bear any damage brought by late and inaccurate news.
4.If the news we published involves copyright of yours,just let us know.

BRIEF INTRODUCTION

Cnbearing is the No.1 bearing inquiry system and information service in China, dedicated to helping all bearing users and sellers throughout the world.

Cnbearing is supported by China National Bearing Industry Association, whose operation online is charged by China Bearing Unisun Tech. Co., Ltd.

China Bearing Unisun Tech. Co., Ltd owns all the rights. Since 2000, over 3,000 companies have been registered and enjoyed the company' s complete skillful service, which ranking many aspects in bearing industry at home and abroad with the most authority practical devices in China.